Mainly used for drilling water wells, monitoring wells, geothermal air condition ing hole construction, national defense projects,anti-floating anchor rod,cable anchor rod,high-pressure Rotary Jet Drilling Operations;At the same time, it is suitable for large diameter vertical hole construction in geotechnical engineer- ing such as hydropower station,railway,highway and city foundation, grouting reinforcement hole, small foundation pile holemicro-pile etc..
Construction Features:
1.The power head of drilling rig can change speed both mechanically and hydraulically. Suitable for down-hole Hammer,eel pipe, full casing and alloy rotary drilling methods.
2.Two large cylinders on the mast, lifting force up to 25 tons, eccentric with pipe drilling can be used to pull out casing,but also for small-scale non-excavation construction.
3.The rig uses inside and outside telescopic mast power head travel up to 7 meters, can drill 23 meters drill pipe at a time, reduce a time to add drill pipe, improve efficiency twice.
Hydraulic Drilling Rig,Hydraulic Rig Machine,Hydraulic Piling Machine,Hydraulic Drilling Machine JIANGSU XI TEC ENVIRONMENTAL&DRILLING EQUIPMENT COMPANY CO.LTD , https://www.sjxitecdrilling.com
Oxygen valve works
Oxygen valve in physical chemistry experiments, often to use oxygen, nitrogen, hydrogen, argon and other gases. These gases are generally stored in a dedicated high-pressure gas cylinder. When using the pressure reducing valve to gas pressure drop to the required range of experiments, and then through the other control valve fine-tuning, the gas input system. Oxygen valve is the most commonly used oxygen regulator, referred to as oxygen meter. First, the working principle of oxygen valve Oxygen valve high pressure chamber connected with the cylinder, low pressure chamber for gas exports, and leading to the use of the system. Indication of high pressure gauge is the pressure of gas stored in the cylinder. Low pressure gauge outlet pressure can be controlled by adjusting screw. Turn on the main switch when using, and turn the low pressure gauge pressure adjusting screw clockwise to compress the main spring and drive the diaphragm, spring pad and ejector lever to open the valve. Such imports of high-pressure gas from the high-pressure chamber after throttling decompression into the low-pressure chamber, and through the exit leading to the working system. Turn the adjustment screw to change the height of the valve opening to regulate the passage of high-pressure gas and achieve the desired pressure value. Oxygen valves are equipped with safety valve. It is to protect the pressure relief valve and make it safe to use the device, but also the valve failure signal device. If due to the valve pad, valve damage or for other reasons, resulting in the pressure on the outlet and rise above a certain allowable value, the safety valve will automatically open the exhaust. Second, the use of oxygen valves (1) according to the different requirements of use, oxygen valve has many specifications. Most of the highest import pressure, the minimum import pressure of not less than 2.5 times the outlet pressure. Export pressure specifications more generally, the maximum outlet pressure. (2) When installing the pressure reducing valve, make sure its connection specifications are consistent with the cylinder and the system using the connector. Pressure reducing valve and cylinder with hemispherical connection, by tightening the nut so that the two completely match. Therefore, the use of the two hemispherical surfaces should be kept clean to ensure a good airtight effect. Use high-pressure gas to blow off the dust before installation. If necessary, PTFE and other materials can also be used for gaskets. (3) oxygen valve should be prohibited contact with grease, so as to avoid fire accidents. (4) stop working, the relief valve should be more than air net, and then loosen the adjustment screw to prevent long-term compression of the elastic deformation. (5) Oxygen valve should avoid shock and vibration, not with corrosive substances. Third, other oxygen valves, gas pressure relief valve The use of these valves and precautions and oxygen valve is basically the same. However, it should also be noted that special pressure relief valves are generally not used for other gases. In order to prevent misuse, some special pressure reducing valve with a special connection between the cylinder. For example, hydrogen and propane are used left-tooth thread, also known as reverse thread, installation should pay special attention. This keyword search: Jiuding Automatic Control Equipment Co., Ltd. valve supply information